transient voltage suppressors sa series speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. electronic s circuit prote ct io n system
page:1 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - s a series features mechanical characteristics rating symbol value units peak pulse power dissipation by 10x1000s test waveform (fig.1)(note 1) p ppm 500 watts steady state power dissipation on ini? nite heat sink at tl=75c (fig. 5) p d 3 watts peak forward surge current, 8.3ms single half sine wave unidirectional only (note 2) i fsm 70 amps maximum instantaneous forward voltage at 25a for unidirectional only (note 3) v f 3.5/5.0 v operating junction and storage temperature range. t j , t stg -55c to 175c c typical thermal resistance junction to lead r ujl 20 c/w typical thermal resistance junction to ambient r uja 75 c/w notes: 1. non-repetitive current pulse , per fig. 3 and derated above t a = 25 c per fig. 2. 2. measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 perminute maximum. 1. halogen-free 2. rohs compliant 3. typical maximum temperature coef ?cient 4. v br =0.1%xv br @25c x t 5. glass passivated chip junction in p600 package 6. 500w peak pulse capadility at 10x1000s waveform,repetition rate (duty cycles):0.01% 7. fast response time:typically less than 1.0ps from 0 volts to bv min 8. excellent clamping capability 9. low incremental surge resistance 10. typical ir less than 5a above 12v 11. high temperature soldering guaranteed: 260c/40 seconds / 0.375, \(9.5mm) lead length, 5lbs., (2.3kg)tension 12. plastic package has underwriters laboratory fammability classi?cation 94v-0 tvs devices are ideal for the protection of i/o interfaces,vcc bus and other vulnerable circuits used in telecom, computer , industrial and consumer electronic applications. uni bi uni bi anode cathode applications circuit prote ct io n system
transient voltage suppressors - sa series page:2 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. electriacl characteristics type number reverse stand- off voltage breakdown voltage@i t test current maximum clamping voltage@i peak pulse current reverse leakage (uni) (bi) (v) br min. (v) br.max. (v) t (ma) c (v) (a) (a) sa5.0a sa5.0ca 5.0 6.40 7.00 10 9.2 55.4 600 sa6.0a sa6.0ca 6.0 6.67 7.37 10 10.3 49.5 600 sa6.5a sa6.5ca 6.5 7.22 7.98 10 11.2 45.5 400 sa7.0a sa7.0ca 7.0 7.78 8.60 10 12.0 42.5 150 sa7.5a sa7.5ca 7.5 8.33 9.21 1 12.9 39.5 50 sa8.0a sa8.0ca 8.0 8.89 9.83 1 13.6 37.5 25 sa8.5a sa8.5ca 8.5 9.44 10.40 1 14.4 35.4 10 sa9.0a sa9.0ca 9.0 10.00 11.10 1 15.4 33.1 sa10a sa10ca 10.0 11.10 12.30 1 17.0 30.0 sa11a sa11ca 11.0 12.20 13.50 1 18.2 28.0 sa12a sa12ca 12.0 13.30 14.70 1 19.9 25.6 sa13a sa13ca 13.0 14.40 15.90 1 21.5 23.7 sa14a sa14ca 14.0 15.60 17.20 1 23.2 22.0 sa15a sa15ca 15.0 16.70 18.50 1 24.4 20.0 sa16a sa16ca 16.0 17.80 19.70 1 26.0 19.6 sa17a sa17ca 17.0 18.90 20.90 1 27.6 18.5 sa18a sa18ca 18.0 20.00 22.10 1 29.2 17.5 sa20a sa20ca 20.0 22.20 24.50 1 32.4 15.7 sa22a sa22ca 22.0 24.40 26.90 1 35.5 14.4 sa24a SA24CA 24.0 26.70 29.50 1 38.9 13.1 sa26a sa26ca 26.0 28.90 31.90 1 42.1 12.1 sa28a sa28ca 28.0 31.10 34.40 1 45.4 11.2 sa30a sa30ca 30.0 33.30 36.80 1 48.4 10.5 sa33ca 33.0 36.70 40.60 1 53.3 9.6 sa36a sa36ca 36.0 40.00 44.20 1 58.1 8.8 sa40a sa40ca 40.0 44.40 49.10 1 64.5 7.9 sa43a sa43ca 43.0 47.80 52.80 1 69.4 7.3 sa45a sa45ca 45.0 50.00 55.30 1 72.7 7.0 sa48a sa48ca 48.0 53.30 58.90 1 77.4 6.6 sa51a sa51ca 51.0 56.70 62.70 1 82.4 6.2 sa54a sa54ca 54.0 60.00 66.30 1 87.1 5.0 sa58a sa58ca 58.0 64.40 71.20 1 93.6 5.4 sa60a sa60ca 60.0 66.70 73.70 1 96.8 5.3 sa64a sa64ca 64.0 71.10 78.60 1 103.0 5.0 sa70a sa70ca 70.0 77.80 86.00 1 113.0 4.5 sa75a sa75ca 75.0 83.30 92.10 1 121.0 4.2 sa78a sa78ca 78.0 86.70 95.80 1 126.0 4.0 sa85a sa85ca 85.0 94.40 104.00 1 137.0 3.7 sa90a sa90ca 90.0 100.00 111.00 1 146.0 3.5 sa100a sa100ca 100.0 111.00 123.00 1 162.0 3.1 sa110a sa110ca 110.0 122.00 135.00 1 177.0 2.0 sa120a sa120ca 120.0 133.00 147.00 1 193.0 2.6 sa130a sa130ca 130.0 144.00 159.00 1 209.0 2.4 sa150a sa150ca 150.0 167.00 185.00 1 243.0 2.1 sa160a sa160ca 160.0 178.00 197.00 1 259.0 2.0 sa170a sa170ca 170.0 189.00 209.00 1 275.0 1.9 sa180a sa180ca 180.0 200.00 233.00 1 289.0 1.7 circuit prote ct io n system
page:3 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - s a series ratings and characteristic curves figure 1 - p eak pulse p owe r rating cur ve figure 2 - pulse der ating cur ve figure 3 - pulse w av ef or m figure 4 - t ypical junction capacitanc e figure 5 - st eady stat e po we r der ating cur ve figure 6 - maximum non-repetiti ve p eak f orwa rd surg e curr ent p ppm - peak pulse power (kw) 01.s 1.0s 10s 100s 1.0ms 10ms 0.1 1 10 30 non-repetitive puls e waveform shown in fig. 3 t a =25?c t d - pulse width (sec. ) p p p t d t d t d half sine exponential square i ppm - p eak pu lse curr ent, % i rsm 0 0 50 10 0 15 0 1. 0 2.0 3.0 4.0 t r =1 0sec p eak v alue i ppm i ppm 2 t j =25c as the point where the peak cur rent decays to 50% of i ppm 10 /1 00 0sec. w aveform t d t-t ime (ms) half v alue i ppm ( ) t a - ambient t emperature (oc) peak pulse power (p pp ) or current (i pp ) derating in percentage, % 0 0 25 25 50 50 75 75 100 100 1251 50 1752 00 1 10 10 0 1000 1000 0 1. 01 0. 01 00 .0 1000 .0 cj (p f) tj =2 5c f= 1.0m hz vs ig =5 0m vp -p un i- di re ct io na l v= 0v bi -d ir ec ti onal v= 0v uni-directional @ v r bi-directional @ v r v br - reverse breakdown vo ltage (v) 0 0. 5 1 1. 5 2 2. 5 3 3. 5 02 55 07 51 00 12 51 50 17 52 00 st ea dy s tate po wer di ss ip at io n (w ) t l - lead te mp er at ur e( oc ) l = 0.375? (9.5mm) lead lengths 0 10 20 30 40 50 60 70 80 0 0 1 0 1 1 nu mb er of cy cl es at 60 hz i fsm - peak forward surge current (a) circuit prote ct io n system
transient voltage suppressors - sa series page:4 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. soldering parameters fefow condition lead-free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(min) ) 200c - time (min to max) (t s ) 60-180 secs average ramp up rate (liquidus temp (t l ) to peak 3c/second max t s(max) to t l - ramp-up rate 3c/second max refow - temperature (t l ) (liquidus) 217c - time (min to max) (t s ) 60-150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20-40 seconds ramp-down rate 6c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c t ( e r u t a r e p m e t) ti me (t) t s(min) t s(max) t l t p t s preheat t l t p e n o z l a c i t i r c p u - p m a r t l to t p ramp-dow n physical specifcations weight 0.045oz., 1.2g case jedec do-201 molded plastic body over passivated junction. polarity color band denotes the cathode except bipolar. termina matte tin axial leads, solderable per jesd22-b102d. flow/wave soldering peak temperature : 265c dipping time : 10 seconds soldering : 1 time environmental specifcations temperature cycle jesd22-a104 pressure cooker jesd 22-a102 high temp. storage jesd22-a103 htrb jesd22-a108 thermal shock jesd22-a106 circuit prote ct io n system
page:5 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - s a series dimensions storage conditions: 1. storage temperature: -10c~+40c 2. relative humidity:75%rh 3. keep away from corrosive atmosphere and sunlight. period of storage: 1 year warehouse storage conditions of products packaging part number component package quantity packaging option packaging speci?cation saxxxxx do-204ac 2000 tape & reel ela std rs-296e saxxxxx-b do-204ac 500 bulk concord packing spec c d dim inches millimeters min max min max 1.000 25.40 0.230 0.300 5.80 7.60 c 0.028 0.034 0.71 0.86 d 0.104 0.140 2.60 3.60 unit:mm part numbering system do-204ac (do-15) 5 t t ape xxxx x x circuit prote ct io n system
page:6 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. ruilongyuan electronics co., ltd. reproducing and modifying information of the document is prohibited without permission from ruilongyuan international inc. ruilongyuan international inc. reserves the rights to make changes of the content herein the document anytime without noti?cation. please refer to our website for the latest document. ruilongyuan international inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. ruilongyuan international inc. does not assume any and all implied warranties, including warranties of ?tness for particular purpose, non-infringement and merchantability. applications shown on the herein document are examples of standard use and operation. customers are responsible in comprehending the suitable use in particular applications.ruilongyuan international inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. the products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify ruilongyuan international inc. for any damages resulting from such improper use or sale. tel: +86-755-8290 8296 fax: +86-755-8290 8002 e-mail: jack@ruilon.com circuit prote ct io n system
|
